• Control acces CARDAX
• Control acces KANTECH
• Control acces ROSSLARE
• Bariere auto
• Porti acces VIP
• Turnicheti
• Monitorizare interventie
• Paza umana
• Transport valori
• Consultanta pentru solutii de securitate

JA-80K OASiS

The JA-80K control panel has 50 addresses for wireless devices and 2 hard wired
inputs. OASiS uses a reliable communication protocol at 868 MHz. Maximum
protection of wireless communication is guaranteed by the use of floating code
and digital transmission technology. Installation into a building is very fast and
there are nearly no changes to the interior when using wireless detectors.
Programming can be easily done via a connected computer or remotely using the
relevant communicators. OASiS wireless detectors use 3V lithium batteries with a
3 year lifetime in common operation. The system checks batteries regularly and
signals replacement requirements.
Assigning detectors to sections A, B and C allows the individual security
requirements of different parts of buildings to be met. The control panel allows
you to either use two levels of partial setting (set section A, set sections AB or the
whole system – sections ABC) or to split the system into two independent
subsystems with a common section. The control panel is operated by keypads,
remote controls or remotely for example by mobile phone via a suitable
communicator. There is a built in RFID card reader in the keypad. Cards can be
used independently or their use can be qualified with the use of a code for
increased security. The system can be operated with up to 50 access cards or
codes. Important information about operation of the system is registered in the
internal memory of the control panel, where the last 255 events are saved with
the date and time. With a suitable communicator the system can report selected
events in the form of an SMS to a mobile phone, send all details to an ARC, but
also inform an installer about the required service.
It also allows remote access to the system. It is possible to program the system,
set/unset, monitor the system or control devices in a building  (heating, Venetian
blinds, lighting etc.) via mobile phone or internet. There are three optional
communicators supplied with the system – GSM, combined LAN/PSTN and voice
communicator.
The voice communicator can be combined with a GSM or LAN communicator.
In addition to control devices via its outputs, the control panel also offers many
other useful automation functions.
It optimises the regulation of heating and energy savings together with wireless
thermostats. The control panel sends all the important control commands via
radio, to wireless relay modules in range of the control unit. The communication
range of wireless devices is hundreds of metres, depending on conditions. The
wide availability of wireless detectors, remote controls, sirens and automation
modules gives maximum freedom to achieve the most suitable solution to
individual customer requests. The simple design of detectors allows installation of
the OASiS system into all interiors. The system was developed with an eye for
clean and fast installation (built-in mains-powered supply, optional communicator
modules, convenient programming by PC and Internet) and most of all for easy
and transparent operation and monitoring of the system by the customer. All the
texts used by OASiS for communication with its owner are editable to provide
information about events in a clear and understandable way.

CARACTERISTICI  TEHNICE:

• No. of wireless zones 50
• No. of hardwired zones 2 balanced
• Communication band 868 MHz
• Zone bypassing permanently or temporarily
• No. of sections for partial armed mode 3 – A, B, C
• No. of subsystems for a split system 2 with a common section
• No. of access codes 50 (+ 1 service code)
• No. of access cards 50
• Events memory 255 events including date, time
• Voltage 230 V, 50 Hz
• Back up battery 12 V, 1.3 Ah or 2.6 Ah
• Back up power supply output
• 12 V, 400 mA permanently, intermittently up to 1 A
• External warning output relay max. 1 A/60 V
• Internal warning output switching to GND, max. load 0.5 A
• Programmable outputs PgX, PgY, max. 0.1 A, switching to GND
• Dimensions 258 x 214 x 77 mm

The JA-80V communicator is used for reporting events and communication via a
LAN (Ethernet) computer network and also via a PSTN line.
It allows reporting events in the form of SMS messages (up to 8 phone numbers),
reporting events by phone calls with the forwarding of an acoustic signal and data
forwarding to 2 ARCs. The communicator allows two-way remote access to the
control panel. It is possible to operate and program the system remotely via
phone (dial in and use of keypad or via SMS commands) or via secure internet
page www.GSMLink.cz. It is possible to connect the communicator either to a LAN
network or to PSTN line. If only the PSNT line is connected, it is possible to
operate the system remotely via phone, report events via SMS, make phone calls
and report to one ARC in CID protocol. If there is only a LAN connection then
remote access via the Internet and event reporting to one ARC in IP CID protocol
is possible.

JA-80Y GSM/GPRS communicator

This module uses the GSM mobile phone network. It allows remote access to the
system by mobile phone or via the Internet. It can also report events from the
system to mobile phones and to alarm receiving centres (monitoring). It also
provides a simulated telephone line (GSM gateway feature).

The communicator is designed to be installed within the control panel housing.
When connected to a GSM network it allows the following:

• event reporting by SMS (to up to 8 telephone numbers)
• event reporting by phone call with an acoustic warning
• event reporting to an ARC (Automatic Receiving Centre – also known as a Central Monitoring Station) - up to 2 ARCs
• remote control and programming by phone (remotely authorizing a phone keypad or by SMS instructions)
• the remote control of appliances in the house by dialling in from an authorized number (free of charge with unanswered calls)
• remote control and programming via the Internet (www.GSMlink.cz)
• connecting a phone set = simulated tel. line = GSM gateway function (incl. CLIP protocol = caller ID and SMS transfer)
• listening-in and voice communication – via a connected SP-02 intercom
• connecting a PC to the Internet (GPRS modem feature)

Specifications

JA-80X voice communicator

The JA-80X voice module is used for the reporting of voice messages from the
OASiS system via a PSTN line. It allows the recording of up to 6 voice messages
which can be forwarded to up to 4 phone numbers. The communicator can also
forward reports to ARCs in CID protocol. It is connected to the control panel bus
by an RJ cable and it is possible to install it separately or in connection to a JA-80Y
or JA-80V communicator. The communicator allows remote operating and
programming of the system from a phone by DTMF commands.

Wireless External Siren - JA-80A

The JA-80A wireless external siren is used for wireless communication with radio
control panels of the JA-8x line. The siren is totally wireless, powered only by a
lithium battery and there is no need for an external supply. Installation is
therefore easily done and there is no need to find suitable supplies in the attic
and a difficult power supply solution is avoided. The siren warns the surrounding
area when a building is intruded. Handling which is not authorised such as tearing
the siren off the wall, opening the cover etc is signalled to the system.
Communication with the control panel is  two-way. The siren regularly checks its
functions, battery status and checks transmissions to keep the radio connection.

Specifications

JA-80L wireless internal siren

   The JA-80L is a mains-powered (230V AC) siren which sounds an alarm, and
exit/entrance delays. If disconnected from the power while it sounds an alarm,
it reports tampering to the system (i.e. intruder verification). Can also be used as
a doorbell and as acoustic indication of detector triggering. Its indicator function
is programmable. The siren can be enrolled to the control panel and also wireless
detectors, RC controllers, wireless keypad inputs and the JA-80H door bell button
can be enrolled to it to generate the desired sound.
   It can be used as the following: An indoor alarm siren A wireless door bell A
detector-triggered chime A sounder for entrance and exit delay beeps Thief
verification The siren is mains-powered and communicates via OASIS wireless
protocol. It can form part of an alarm system or be used as a stand-alone device.
When used as part of an alarm system, it sounds when an intruder alarm has
been triggered and confirms the actual presence of an intruder in the building by
sending a tamper signal when it gets unplugged. Installation shall only be
undertaken by qualified technicians holding a training certificate issued by an
authorized distributor.

Specifications

SW-01

The RP-01 system can be connected to the PC via the SW-01 interface and
software. In the system the interface is
connected between the RS-485 bus and
any free USB slot on the PC. Software
called RFIDprog allow s you to setup,
manage and control the system